Background: Iatrogenic ureteral injury is an increasing concern in the laparoscopic era, affecting both patient morbidity and costs. Current techniques enabling intraoperative ureteral identification require invasive procedures or radiations. Our aim was to develop a real-time, non-invasive, radiation-free method to visualize ureters, based on near-infrared (NIR) imaging. For this purpose, we interfered with the biliary excretion pathway of the indocyanine green (ICG) fluorophore by loading it into liposomes, enabling renal excretion. In this work, we studied various parameters influencing ureteral imaging. Methods: Fluorescence intensity (FI) of various liposomal ICG sizes and doses were characterized in vitro and subsequently tested in vivo in mice and pigs. Quantification was performed by measuring FI in multiple points and applying the ureteral/retroperitoneum ratio (U/R). Results: The optimal liposomal ICG loading dose was 20%, for the different liposomes' sizes tested (30, 60, 100 nm). Higher concentration of ICG decreased FI. In vivo, the optimal liposome size for ureteral imaging was 60 nm, which yielded a U/R of 5.2 $\pm$ 1.7 (p < 0.001 vs. free ICG). The optimal ICG dose was 8 mg/kg (U/R = 2.1 $\pm$ 0.4, p < 0.05 vs. 4 mg/kg). Only urine after liposomal ICG injection had a measurable FI, and not after free ICG injection. Using a NIR-optimized laparoscopic camera, ureters could be effectively imaged in pigs, from 10 min after injection and persisting for at least 90 min. Ureteral peristaltic waves could be clearly identified only after liposomal ICG injection. Conclusions: Optimization of liposomal ICG allowed to visualize enhanced ureters in animal models and seems a promising fluorophore engineering, which calls for further developments.

Solution-based thin-film semiconductors offer a promising path for the mass production of low-cost solar cells prepared at low temperatures. Thin-film Cu-based chalcogenides such as Cu(In,Ga)(S,Se)2 (CIGSSe) and Cu2ZnSn(S,Se)4 (CZTSSe) hold great promise and have been regarded as viable candidates because of the abundance of their constituent elements and environmentally nontoxic nature. This Review summarizes the recent progress in solution-processed Cu chalcogenides (CuInSe2, Cu(In,Ga)(S,Se)2, Cu2ZnSnS4, Cu2ZnSn(S,Se)4) for thin-film solar cells, with emphasis on the precursor solution deposited by spray pyrolysis and spin coating. The general aspects, current status, and recent research highlights are introduced and analyzed in detail. Finally, the challenges and future prospects of these solar cells are also discussed.

Surface engineering is an effective method to improve the thermochromic performance of VO2. In this paper, an acid-etching top down method was proposed to tailor the VO2 surface morphology from the continuous dense-packed surface to patterned structure, which exhibited the enhanced integrated visible transmittance (Tlum) and the enlarged solar modulating abilities (ΔTsol). Moreover, a self-patterning approach was also illustrated to improve the thermochromic properties. The proposed surface engineering methods represent a facile and cost-effective approach for enhancing thermochromic properties that could promote the application of VO2 thin films in smart windows.

More than 50% of solar energy comes from the infrared region (as radiant heat) of the solar spectrum. Electrochromic (EC) materials, which can dynamically modulate the transmittance of infrared (IR) radiation, can be effectively applied in smart windows for thermal management in buildings. In this work, a core-shell TiO2-WO3 inverse opal (IO) structure was fabricated through the electrodeposition of WO3 onto TiO2 IO templates. The TiO2 IO templates were synthesized by introducing TiO2 into the voids of a polystyrene (PS) colloidal crystal template, followed by calcination to remove the PS microspheres. It was found that the TiO2-WO3 IO core-shell structure can modulate NIR transmittance at wavelengths from 700 to 1600 nm in the NIR range when potential is applied in LiClO4/PC electrolyte. When −-0.3 V is applied, up to 60% of NIR radiation in this range can be blocked. The NIR transmittance can be modulated by tuning the applied potential. This study focuses on comparing the novel TiO2-WO3 IO structure with electrodeposited WO3 thin film to fully elucidate the effect of the inverse opal morphology and the TiO2-WO3 hybrid system on the optical properties. Results show that the NIR blockage can be sustained up to 90% after 1200 reversible cycles for TiO2-WO3 IO structure. The greater surface area of the IO structure increases the number of active sites available for the redox reactions by providing a larger contact area with the electrolyte. The more electroactive area with improved charge transfer enhances the overall NIR transmittance contrast as compared to bulk WO3 thin film. Furthermore, the addition of WO3 to TiO2 to form a composite has been shown to enhance cycling performance and device lifespan.

Vanadium dioxide (VO2) is one of the most widely studied inorganic phase change material for energy storage and energy conservation applications. Monoclinic VO2 [VO2(M)] changes from semiconducting phase to metallic rutile phase at near room temperature and the resultant abrupt suppressed infrared transmittance at high temperature makes it a potential candidate for thermochromic smart window application to cut the air-condition usage. Meanwhile proper electrical potential, stable structure and good interaction with lithium ions make metastable VO2 [VO2(B)] an attractive material for fabrication of electrodes for batteries and supercapacitors. However, some long-standing issues have plagued its usage. In thermochromic application, high transition temperature (τc), low luminous transmittance (Tlum) and undesirable solar modulation ability (△Tsol) are the key problems, while in energy storage applications, short cycling lifetime and complex three-dimension microstructure are the major challenges. The common methods to produce VO2 polymorph are physical vapour deposition (PVD), chemical vapour deposition (CVD), sol-gel synthesis, and hydrothermal method. CVD is an intensively studied method due to its ability to produce uniform films with precise stoichiometry, phase and morphology control. This paper reviews the various CVD techniques to produce VO2 with controlled phases and the ternary diagram shows the relationship between film stoichiometry and various process conditions. The difference between the various CVD systems are commented and the process window to produce VO2 are tabulated. Some strategies to improve VO2′s performance in both energy conservation and energy storage applications are discussed.

The invention provides a novel class of solid water-dispersible powders, comprising a plurality of water-insol. photoinitiators in nanoparticle forms for use in water-based ink formulations. [on SciFinder(R)]

The authors describe a general and facile method based on 3D printing methacrylated macromonomers to fabricate shape memory objects that can be used in flexible and responsive elec. circuits. Such responsive objects can be used in fabrication of soft robotics, minimal invasive medical devices, sensors, and wearable electronics. The use of 3D printing overcomes the poor processing characteristics of thermosets and enables complex geometries that are not easily accessible by other techniques. [on SciFinder(R)]

A platform of mechanotactic hybrids is established by projecting lateral gradients of apparent interfacial stiffness onto the planar surface of a compliant hydrogel layer using an underlying rigid substrate with microstructures inherited from 3D printed molds. Using this platform, the mechanistic coupling of epithelial migration with the stiffness of the extracellular matrix (ECM) is found to be independent of the interfacial compositional and topog. cues. [on SciFinder(R)]

Silver grids are attractive for replacing indium tin oxide as flexible transparent conductors. This work aims to improve the electrochem. stability of silver-based transparent conductors. A silver grid/PEDOT:PSS hybrid film with high cond. and excellent stability is successfully fabricated. Its functionality for flexible electrochromic applications is demonstrated by coating one layer of WO3 nanoparticles on the silver grid/PEDOT:PSS hybrid film. This hybrid structure presents a large optical modulation of 81.9% at 633 nm, fast switching, and high coloration efficiency (124.5 cm2 C-1). More importantly, an excellent electrochem. cycling stability (sustaining 79.1% of their initial transmittance modulation after 1000 cycles) and remarkable mech. flexibility (optical modulation decay of only 7.5% after 1200 compressive bending cycles) is achieved. A novel smart supercapacitor is presented that functions as a regular energy-storage device and simultaneously monitors the level of stored energy by a rapid and reversible color variation even at high current charge/discharge conditions. The film sustains an optical modulation of 87.7% and a specific capacitance of 67.2% at 10 A g-1 compared to their initial value at a c.d. of 1 A g-1. The high-performance silver grid/PEDOT:PSS hybrid transparent films exhibit promising features for various emerging flexible electronics and optoelectronic devices. [on SciFinder(R)]

In the absence of water-soluble photoinitiators with high absorbance in the ultraviolet (UV)-visible range, rapid three-dimensional (3D) printing of hydrogels for tissue engineering is challenging. A new approach enabling rapid 3D printing of hydrogels in aqueous solutions is presented on the basis of UV-curable inks containing nanoparticles of highly efficient but water-insoluble photoinitiators. The extinction coefficient of the new water-dispersible nanoparticles of 2,4,6-trimethylbenzoyl-diphenylphosphine oxide (TPO) is more than 300 times larger than the best and most used commercially available water-soluble photoinitiator. The TPO nanoparticles absorb significantly in the range from 385 to 420 nm, making them suitable for use in commercially available, low-cost, light-emitting diode-based 3D printers using digital light processing. The polymerization rate at this range is very fast and enables 3D printing that otherwise is impossible to perform without adding solvents. The TPO nanoparticles were prepared by rapid conversion of volatile microemulsions into water-dispersible powder, a process that can be used for a variety of photoinitiators. Such water-dispersible photoinitiator nanoparticles open many opportunities to enable rapid 3D printing of structures prepared in aqueous solutions while bringing environmental advantages by using low-energy curing systems and avoiding the need for solvents.[on SciFinder (R)]

Cerebral malaria (CM) is a major cause of death of Plasmodium falciparum infection. Misdiagnosis of CM often leads to treatment delay and mortality. Conventional brain imaging technologies are rarely applicable in endemic areas. Here we address the unmet need for a simple, non-invasive imaging methodology for early diagnosis of CM. This study presents the diagnostic and therapeutic monitoring using liposomes containing the FDA-approved fluorescent dye indocyanine green (ICG) in a CM murine model. Increased emission intensity of liposomal ICG was demonstrated in comparison with free ICG. The Liposomal ICG’s emission was greater in the brains of the infected mice compared to naive mice and drug treated mice (where CM was prevented). Histological analyses suggest that the accumulation of liposomal ICG in the cerebral vasculature is due to extensive uptake mediated by activated phagocytes. Overall, liposomal ICG offers a valuable diagnostic tool and a biomarker for effectiveness of CM treatment, as well as other diseases that involve inflammation and blood vessel occlusion.[on SciFinder (R)]

Nanostructured thin films are important in the fields of energy conversion and storage. In particular, multi-layered nanostructured films play an important role as a part of the energy system for energy saving applications in buildings. Inkjet printing is a low-cost and attractive technol. for patterning and deposition of multi-layered nanostructured materials on various substrates. However, it requires the development of a suitable ink formulation with optimum viscosity, surface tension and evapn. rate for various materials. In this study, a versatile ink formulation was successfully developed to prep. NiO and WO3 nanostructured films with strong adhesion to ITO coated glass using inkjet printing for energy saving electrochromic applications. We achieved a high performance electrochromic electrode, producing porous and continuous electrochromic films without aggregation. The NiO film with 9 printed layers exhibits an optical modulation of 64.2% at 550 nm and a coloration efficiency (CE) of 136.7 cm2 C-1. An inkjet-printed complementary all solid-state device was assembled, delivering a larger optical modulation of 75.4% at 633 nm and a higher CE of 131.9 cm2 C-1 among all solid-state devices. The enhanced contrast is due to the printed NiO film that not only performs as an ion storage layer, but also as a complementary electrochromic layer. [on SciFinder(R)]

Single-walled carbon nanotubes (SWCNTs) are considered pivotal components for mol. electronics. Techniques for SWCNT lithog. today lack simplicity, flexibility, and speed of direct, oriented deposition at specific target locations. In this paper SWCNTs are directly drawn and placed with chem. identification and demonstrated orientation using fountain pen nanolithog. (FPN) under ambient conditions. Placement across specific elec. contacts with such alignment is demonstrated and characterized. The fundamental basis of the drawing process with alignment has potential applications for other related systems such as inorg. nanotubes, polymers, and biol. mols. [on SciFinder(R)]

The invention provides novel means for fabricating patterns and objects comprising nanorods, while reducing inter-particle interaction. [on SciFinder(R)]

The growing interest in the field of three-dimensional printing has led to great demand for new materials. In this paper we should like to present a new ink for printing porous structures that can be used for embedding various functional materials. The ink is composed of a UV polymerizable oil-in-water emulsion which converts into a solid object upon UV irradiation, and upon evaporation of the aqueous phase, forms a porous structure. The 3D objects with their various porosities, were printed by a Digital Light Processing (DLP) printer. The total surface area of the object can be controlled by changing the emulsion’s droplets size and the dispersed phase fraction. The printed 3D porous structures can be used in a variety of applications, and here we show a composite conductive object, made of silver and cross-linked polymer. After the porous object is formed, the pores are filled by vacuum, dipping in a dispersion of silver nanoparticles, followed by chemical sintering at room temperature, which results in conductive percolation paths within the 3D structure. Application of this structure is demonstrated for use as a 3D connector of an electrical circuit. [ABSTRACT FROM AUTHOR]Copyright of Journal of Materials Chemistry C is the property of Royal Society of Chemistry and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder’s express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The formation of 3D objects composed of shape memory polymers for flexible electronics is described. Layer-by-layer photopolymerization of methacrylated semicrystalline molten macromonomers by a 3D digital light processing printer enables rapid fabrication of complex objects and imparts shape memory functionality for electrical circuits.

A method of manufg. an electrochromic device is provided. The method includes providing a patterned arrangement of an elec. conductive material; and applying one or more layers of an electrochromic material to the patterned arrangement, wherein at least a portion of the electrochromic material is in elec. contact with the elec. conductive material. An electrochromic device and an electrochromic ink compn. are also provided. [on SciFinder(R)]

Permethrin, a poorly water-soluble synthetic pesticide belonging to the pyrethroid family, was formulated into water-dispersive nanometric form by rapid evaporation of pesticide loaded oil-in-water microemulsion. The mean hydrodynamic diameter of Nanopermethrin was found to be 199.01 ± 1.4 nm. The efficacy of the Nanopermethrin was comparatively investigated with its bulk form against 2-3 days old adult mosquitoes by WHO cone bioassay for 60 min. The median knockdown concentration of Culex tritaeniorhynchus, Culex quinquefasciatus and Aedes albopictus were found to be 7.20 × 10(4), 7.53 × 10(4), 0.42 × 10(3) mg/L for Bulk permethrin, and 0.98 × 10(4), 1.17 × 10(4), 0.05 × 10(3) mg/L for Nanopermethrin, respectively. The obtained results extrapolate the improved efficacy of Nanopermethrin even at low-level concentrations. Hence, the formulated Nanopermethrin will serve as an effective alternative pesticide in controlling the mosquito population with reduced environmental toxicity.[on SciFinder (R)]