The methods of the invention permit design modalities which are currently unavailable in the printing of scintillating materials and objects, significantly reducing difficulties assocd. with manuf. of scintillating materials, decrease development time and assocd. costs. [on SciFinder(R)]

Vanadium dioxide (VO2), with a reversible phase transition near ambient temperature, has been found to be a promising candidate for energy-saving smart windows. However, its use is constrained by its low visible transmission (Tlum) and high transition temperature (τc). In this paper, by codoping tungsten (W) and magnesium (Mg) in VO2, a good combination of low τc (\~35 °C) and high Tlum (81.3%) was achieved. The τc declines with decreasing Mg doping level in Mg/W-codoped samples, which is the opposite effect of doping with only Mg, suggesting a synergistic effect of the two dopants arising from the e- and h+ carrier neutralization. In addition, the band gap of Mg/W-codoped VO2 was gradually widened; this is attributed to the depressed absorption, which enhanced the Tlum. [ABSTRACT FROM AUTHOR]Copyright of Journal of Materials Chemistry C is the property of Royal Society of Chemistry and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder’s express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The use of printing to produce 2D arrays is well established, and should be relatively facile to adapt for the purpose of printing biomaterials; however, very few studies have been published using enzyme solns. as inks. Among the printing technologies, inkjet printing is highly suitable for printing biomaterials and specifically enzymes, as it offers many advantages. Formulation of the inkjet inks is relatively simple and can be adjusted to a variety of biomaterials, while providing nonharmful environment to the enzymes. Here we demonstrate the applicability of inkjet printing for patterning multiple enzymes in a predefined array in a very straightforward, noncontact method. Specifically, various arrays of the enzymes glucose oxidase (GOx), invertase (INV) and horseradish peroxidase (HP) were printed on aminated glass surfaces, followed by immobilization using glutardialdehyde after printing. Scanning electrochem. microscopy (SECM) was used for imaging the printed patterns and to ascertain the enzyme activity. The successful formation of 2D arrays consisting of enzymes was explored as a means of developing the first surface confined enzyme based logic gates. Principally, XOR and AND gates, each consisting of two enzymes as the Boolean operators, were assembled, and their operation was studied by SECM. [on SciFinder(R)]

This work describes a novel supercapacitor electrode based on a glass fiber felt substrate, single-walled carbon nanotube (SWCNT) and metal oxide layers (RuO2 or MnO2). It is fabricated by the repeated and alternate deposition of SWCNTs and metal oxides via dipping and electrodeposition, resp., to achieve three-dimensional layered hierarchical structured supercapacitor electrodes. The results show that the layered structured electrodes fabricated by alternating deposition of SWCNTs and metal oxides have higher capacitance as compared with the bulk deposited samples, which are fabricated by deposition of SWCNTs followed by metal oxides. The best configuration studied in this work shows specific capacitance of 72 and 98 F/g for the SWCNT-MnO2 and SWCNT-RuO2, resp., whereas the corresponding areal capacitances are 0.07 and 0.09 F/cm2. This three-dimensional porous electrode structure design combines the high mech. stability of the felt substrate with the high cond. and sp. surface area of SWCNTs, and the high capacitance of metal oxides. This will add immensely to the research and development of wearable lightwt. electronics in harsh environments. [on SciFinder(R)]

This study presents a method for one step incorporation of lipophilic compounds in hydrophilic nanofibers. By this method nanodroplets of oil and of volatile solvent are entrapped within polymer nanofibers during an electrospinning process. While performing the process with a volatile oil with dissolved lipophilic material, such as the drug celecoxib, nanofiber–nanoparticle composites are formed. The polymer used to form the fibers is a high molecular weight poly(vinyl alcohol) which enables rapid dissolution and release of the incorporated lipophilic material. The resulting celecoxib nanoparticles that are embedded within the nanofiber are amorphous and their average size is in between 21 and 93nm, thus potentially lead to their increased dissolution rate. The preparation of such a solid matrix containing nanodroplets or nanoparticles may be applied as a fast dissolving delivery system for water insoluble materials.

The patterning of various 2D and 3D substrates is accomplished using a new method, reactive transfer printing, combined with a self-reducing copper precursor. The ink composed of the metal precursor is printed on a donor substrate; during its decomposition, the metal is transferred to an acceptor substrate. This process is demonstrated with copper formate as the precursor, forming a copper pattern with excellent conductivity (50% that of bulk copper).

The invention provides a process of forming a continuous pattern on a surface composed of two or more surface regions, each of the regions being of a different surface energy, the process utilizing a novel ink formulation for printing on such multi-region surfaces. [on SciFinder(R)]

This work reports on the prepn. of semitransparent perovskite solar cells. The cells transparency is achieved through a unique wet deposition technique that creates perovskite grids with various dimensions. The perovskite grid is deposited on a mesoporous TiO2 layer, followed by hole transport material deposition and evapn. of a semitransparent gold film. Control of the transparency of the solar cells is achieved by changing the perovskite soln. concn. and the mesh openings. The semitransparent cells demonstrate 20-70% transparency with a power conversion efficiency of 5% at 20% transparency. This is the first demonstration of the possibility to create a controlled perovskite pattern using a direct mesh-assisted assembly deposition method for fabrication of a semitransparent perovskite-based solar cell. [on SciFinder(R)]

Highly conductive copper patterns on low-cost flexible substrates are obtained by inkjet printing a metal complex based ink. Upon heating the ink, the soluble complex, which is composed of copper formate and 2-amino-2-methyl-1-propanol, decomposes under nitrogen at 140 °C and is converted to pure metallic copper. The decomposition process of the complex is investigated and a suggested mechanism is presented. The ink is stable in air for prolonged periods, with no sedimentation or oxidation problems, which are usually encountered in copper nanoparticle based inks.  

The invention relates to a light-absorbing element coated on at least a region of its surface with a film of at least one light-absorbing material, the light-absorbing material being assocd. with at least one binder material, the film being 1 - 20 μm thick and having light absorption of at least 90%. The invention also relates to a device comprising a light-absorbing element. The invention also claims a thermosolar device comprising a light-absorbing element. The invention also relates to a method of fabricating a light-absorbing film on a surface region of a substrate, the method comprising: (a) forming on a surface region at least one absorbing layer comprising: (I) a light-absorbing material; and (II) a polymerizable binder resin; (b) heating the at least one absorbing layer to induce polymn. of the binder resin; and (c) optionally forming at least one IR radiation reflecting layer on the polymd. binder. [on SciFinder(R)]

Stray light, also known as optical noise, affects the performance of many optical devices. It can be reduced to a tolerable level by well-designed and well-baffled system or/and by using functional black coatings that are fabricated in a complex and costly process. Carbon nanotubes (CNTs) absorb light strongly, making them an ideal candidate for realizing a super black coating. CNT coatings were formed by spraying formulations composed of a silicon binder and low cost multiwalled CNTs on a pre-heated aluminum plate. The diffuse reflectance of the coatings in the VIS range (350-800nm) was in the range of 2.6-5.11%, depending on the MWCNT concentration in the coating. In the NIR range (850-2400nm), the reflectance values were in the range of 4-6.5%, however the dependence on MWCNT concentration was not very significant. Excellent adhesion to the aluminum substrates was achieved, for coatings with CNT concentration below 15%, while still having very low reflectance, even at temperature c

We report on the biological performance of organic nanoparticles formed by a simple method based on rapid solvent removal from a volatile microemulsion. The particular focus of the study was on testing the suitability of the method for substances soluble in partially water-miscible organic solvents as well as on evaluating the therapeutic activity of the resultant nanoparticles. Curcumin was employed as a model for hydrophobic drugs, and, as it is soluble in water-miscible organic solvents, it was successfully incorporated into a new cyclopentanone-water microemulsion system. During rapid solvent removal by spray-drying, the nanometric droplets of the microemulsion were converted into nanoparticles containing amorphous curcumin with an average size of 20.2 ± 3.4 nm, having a ζ potential of -36.2 ± 1.8 mV. These nanoparticles were dispersible in water and retained the high loading of the active substance. The therapeutic activity of the resulting nanoparticles was demonstrated in a pancreatic cancer cell line, PANC-1. The effective concentration for reducing the metabolic activity by 50% (EC50) was found to be 11.5 mM for nanoparticles compared with 19.5 µM for free curcumin. [ABSTRACT FROM AUTHOR]Copyright of Journal of Materials Chemistry B is the property of Royal Society of Chemistry and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder’s express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

We report on the biological performance of organic nanoparticles formed by a simple method based on rapid solvent removal from a volatile microemulsion. The particular focus of the study was on testing the suitability of the method for substances soluble in partially water-miscible organic solvents as well as on evaluating the therapeutic activity of the resultant nanoparticles. Curcumin was employed as a model for hydrophobic drugs, and, as it is soluble in water-miscible organic solvents, it was successfully incorporated into a new cyclopentanone-water microemulsion system. During rapid solvent removal by spray-drying, the nanometric droplets of the microemulsion were converted into nanoparticles containing amorphous curcumin with an average size of 20.2 ± 3.4 nm, having a ς potential of -36.2 ± 1.8 mV. These nanoparticles were dispersible in water and retained the high loading of the active substance. The therapeutic activity of the resulting nanoparticles was demonstrated in a pancreatic cancer cell line, PANC-1. The effective concentration for reducing the metabolic activity by 50% (EC50) was found to be 11.5 µM for nanoparticles compared with 19.5 µM for free curcumin. [ABSTRACT FROM AUTHOR]Copyright of Journal of Materials Chemistry B is the property of Royal Society of Chemistry and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder’s express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Even the best artists struggle to show us what real-world objects look like in all their three-dimensional (3D) glory. Most of the time that doesn't matter–-looking at a photo or sketch gives us a good-enough idea. But if you're in the business of developing new products and you need to show them off to clients or customers, nothing beats having a prototype: a model you can touch, hold, and feel. Only trouble is, models take ages to make by hand and machines that can make ``rapid prototypes'' cost a fortune (up to a half million dollars). Hurrah, then for 3D printers, which work a bit like inkjets and build up 3D models layer by layer at up to 10 times the speed and a fifth the cost. How exactly do they work? Let's take a closer look!

In this paper we describe the preparation of novel Near Infrared (NIR) fluorescent nanoparticles for application in medical imaging of colorectal tumors. The nanoparticles are prepared by using only non-covalent binding processes of molecules which are approved for clinical use. The preparation process is based on the precipitation of a polycation, Eudragit-RS, followed by sequential adsorption of a blocking protein, sodium caseinate, NIR fluorescent dye, Indocyanine Green (ICG) and optionally, a targeting molecule, anti-CEA antibody. Fluorescence measurements have shown that these nanoparticles have higher resistance to photobleaching and higher quantum yield relatively to free ICG. Imaging experiments in orthotopic colorectal cancer mice models have shown that these fluorescent nanoparticles are capable of binding to LS174T human colon tumors in vivo with high specificity, even without the targeting molecule. These nanoparticles, composed of all FDA approved materials, open the way to clinical bioimaging and diagnostics of colon cancer.

Pharmaceutical compn. comprising nanoparticles configured for enhanced phagocytosis by phagocytic cells and labeled with a near-IR (NIR) fluorescent probe bound to the outer surface thereof are provided, and uses thereof in the detection of activated immune cells in the central nervous system (CNS) of a subject. [on SciFinder(R)]

This is a review on recent developments in the field of conductive nanomaterials and their application in printed electronics, with particular emphasis on inkjet printing of ink formulations based on metal nanoparticles, carbon nanotubes, and graphene sheets. The review describes the basic properties of conductive nanomaterials suitable for printed electronics (metal nanoparticles, carbon nanotubes, and graphene), their stabilization in dispersions, formulations of conductive inks, and obtaining conductive patterns by using various sintering methods. Applications of conductive nanomaterials for electronic devices (transparent electrodes, metallization of solar cells, RFID antennas, TFTs, and light emitting devices) are also briefly reviewed.